Are you facing some technical issues with the extender Setup? Sometimes big to big issues are not always tough. This easy method of Setup would take only 15 minutes. Now let’s look for what are the problems creating issues and distracting the router performance.

Steps for Ap.setup/Login

Follow the Steps of AP Setup of the Netgear router to configure. The device without facing any issues regarding the process:

• Let’s start the process by net login.
• To begin the Setup process first select the WiFi Settings menu.
• Then, choose the WiFi networks which you want to connect with your Netgear
• After that, Enter the password for the same network after a while and save the settings.
• Here, you have to leave your router to Reboot if you are unable to make a network.
• After that, connect the router to the Netgear
• Therefore, connect the extender to a power extension and wait for a moment to boot, and let the existing extender boot up (wait for approx 5 minutes).
• Once your extender meets the bootup levels then attach your system with an ethernet port from any of the existing 4 ports of the Netgear router by using an ethernet cable.
• As a result, wait until your computer connects to the Netgear WiFi router setup wizard, else wait and follow the steps below:
• Finally, select the settings > then network> after that WiFi> therefore, click add network> now select WAN network from list > finally enter the password ‘admin’ > and your process is successfully complete here.

How to Find Out The Router’s Default IP Address?

In most of the Netgear routers the IP is common like, ‘192.168. 1.1.’ You can use the particular IP as the default IP gateway. Although, one dual-band router might vary from another. Therefore, it is necessary to check the IP address of the Netgear router first.

A number of ways can determine the wireless router’s IP address. Are you a Windows 10/11 computer or laptop user? Then, just hold on to the Windows and key simultaneously it can open up the “Settings” of your window and then go for “Network & Internet”.

Then, select the properties by tapping twice on the “Properties” option and scroll down to the page to locate the “IPv4 address”. Here, you can find Netgear’s router’s default gateway IP. In addition to that, you can also use the Windows Command Prompt” tool to easily identify the device IP address.

Press the Windows and X key together and after that choose “Run” when the pop-up menu becomes visible on your screen then you have to “cmd” in the dialogue box and hit “Enter” till the Command Prompt window opens you have to wait for a while and write “IP config/all”. Finally, now press the “Enter” button and then navigate to “Default Gateway” to get the IP address of the router.

Troubleshoot Router Setup Issues

• Just examine the WiFi connection.
• Then, check for the setting of the router.
• After that, just see the router’s firmware.
• Also, see the router’s security settings.
• Inquire about the router’s firewall settings.
• Verify the host configuration of the DHCP router.

Optimize Your Router Settings

Different settings on your router could improve the settings of your signal strength and speed in your home.

• While you play any video game or stream any content, you should prioritize your bandwidth. This strategy is less effective but shares WiFi connections simultaneously.
• On your router, reset the Request to Send thresholds. The data transmission essentially clears. It is the protocol of the RTS threshold.
• Setting your RTS threshold at a lower number can probably increase the WiFi performance. Such as an apartment or a crowded area. Data packets can transfer and improve reliability issues. However, a smaller data packet size will decrease the network performance; While setting it to a threshold.

While the Reset Works For All

If you think the Setup is not doing so then, reset can vanish all the old setups and give you a new way through a Reset button on it. Don’t be confused and just look at the back of the extender. Just look up for a small button mentioned as the Reset button on the Netgear N300 setup. Now, just go and search for a pen from your stand or drawer. Now press this pen inside the small hole. If you see any blue light on your extender it means you are back on the extender with a hold of connection. But, if the red light isn’t leaving it means there are the same issues, and you need to make a call to the provider of the Linksys extender.

 

We mentioned a number of tips and methods to change the Netgear EX3700 setup And router login credentials. But if you still face any problems you can easily contact us through the given chat box. We are here to help you.